1Anetsberger Brothers, Inc.180 North Anets Drive • Northbrook, Illinois 60062 • 847-272-0770 • Fax 847-272-1943For ANETS Factory Warranty Serv
10GAS CONNECTION INSTRUCTIONSInstalling your ANETS Fryer requires the fol-lowing procedure, after its legs or casters are pro-perly attached and i
11FRYER OPERATING INSRUCTIONSDANGERAvoid moving the fryer while it containsHOT shortening. Drain the shortening fromthe fryer before moving it for
12FRYER PREPARATION FOR USE“BOIL OUT” INSTRUCTIONSNew ANETS Fryers are leak-tested and cleanedat the factory before shipping. Before using anewly in
13NOTE: The gas line of a new fryer installationmay contain a considerable amount of air that willhinder immediate lighting. You may have to pressin
14NOTE: Shutdown is recommended at the end ofa workday or whenever no frying is required for aperiod of several hours. The fryer should beshutdown du
15FRYER OPERATING INSTRUCTIONS (Continued)Load the fryer basket with thefood product while the basket isnot in the hot liquid shortening.DO NOT ove
16DAILY CLEANING PROCEDURENOTE: Cleaning is recommended at the end of aworkday, to prepare the fryer for proper operationthe next time it is to be us
17NOTE: Regular maintenance is recommended tokeep the fryer operating properly.Once each month, before beginning fryer opera-tion, check the flue (be
18FRYER TROUBLESHOOTING GUIDEPROBLEM CAUSE REMEDYAll service (repairs or part replacement) must be performed by a qualified Service Agency.Pilot fla
19FRYER TROUBLESHOOTING GUIDE (Continued)PROBLEM CAUSE REMEDYPilot flame goes outrepeatedly.1. Low gas supply pressure [less than 6”W.C. for natura
2CONTENTSShipping Container Inspection ... 3Fryer Gas Supply Specifications ...
20FRYER TROUBLESHOOTING GUIDE (Continued)PROBLEM CAUSE REMEDYMain burners do notignite.1. Gas control valve knob set to OFF orPILOT.2. Low gas supp
21FRYER TROUBLESHOOTING GUIDE (Continued)PROBLEM CAUSE REMEDYMain burners do notstop burning.1. Thermostat has failed.2. Gas control valve has fail
22FRYER TROUBLESHOOTING GUIDE (Continued)PROBLEM CAUSE REMEDYLiquid shortening doesnot reach the desiredtemperature for frying.(Continued)3. (Conti
23LIMITED WARRANTYANETSBERGER BROTHERS, INC., Northbrook, Illinois, USA, certifiesthat all equipment of its manufacture is, to the best of its knowled
24Anetsberger Brothers, Inc.180 North Anets Drive • Northbrook, Illinois 60062 • 847-272-0770 • Fax 847-272-1943Toll-free Customer & Warran
31. Carefully examine the shipping carton forexternal damage. When damage is noted, notifythe delivery carrier immediately. Save all packingmaterial
4Figure 1. Fryer Model 14GS Wiring DiagramFigure 1 is a wiring diagram of anANETS 14GS Fryer. Some fryersmay have other options that do notappear i
5IMPORTANT: Read the Code Requirementsand ALL installation instructions carefully,before starting the installation. Contact thefactory if any proble
6Install the fryer in accordance with the precedingCode Requirements, as well as the followingInstallation Requirements.1. DO NOT install this fryer i
7Figure 3. Typical Leg InstallationINSTALLATION INSTRUCTIONS7. Tighten the four locking nuts evenly andsecurely to hold the leg mounting plate again
8CASTER LEVELING INSTRUC-TIONS1. Move the fryer to its desired location.2. Determine whether the fryer tends to wobbleor rock when in its desired loca
9CASTER LEVELING INSTRUC-TIONS (Continued)5. Completely unscrew the bolts holding thecaster mounting plate that requires levelingadjustment. Retain
Commentaires sur ces manuels